According to the regulations of 743-84 in the list of China's international Gb3 Beijing automobile maintenance center, the fuel consumption ratio is less than 1%. According to the calculation, the engine displacement of 1.6 is - 2.0L, while the oil consumption of 100 km (15 urban cycle conditions) to 10 L vehicles should be less than 1 L / 1000 km, oil consumption and general oil consumption. If you find that the fuel consumption is too high, you should read the following article.

　　漏油导致油耗增加

　　Increased oil consumption due to oil leakage

　　1. 检测方法

　　1. Test method

　　A.应仔细清洁发动机外表面。然后，发动机应启动一段时间，并将其停放在干净的地面上;请再次查看引擎的表面，看是否有漏油的迹象。如果你发现有油滴在某处，这可能就是你要找的漏洞之源。

　　A. The outer surface of the engine should be cleaned carefully first. Then, the engine should be started for a period of time and parked on a clean ground; please check the surface of the engine again for signs of oil leakage. If you find oil drops somewhere, this may be the source of the leak you are looking for.

　　B.用破布塞住发动机的曲轴箱排气(管)和加油嘴，使发动机怠速运转;压缩空气通过测油口或加油喷嘴泵入曲轴箱。这为您提供了一个更可见的石油泄漏视图，并允许您跟踪泄漏源。通过以上检查，基本可以找到漏油现场。

　　B. Plug the crankcase exhaust (pipe) and oil nozzle of the engine with rags to make the engine run at idle speed; the compressed air is pumped into the crankcase through the oil measuring port or oil nozzle. This gives you a more visible view of the oil spill and allows you to track the source of the spill. Through the above inspection, we can basically find the oil leakage site.

　　2.

　　2. Treatment

　　A.所选新垫片应处于良好状态。一旦发现局部断裂等质量问题，不能强力使用。购买新的垫片使用前应在原包装盒中完好地存放，决不随意堆放，使其弯曲或重叠，更不能挂在挂钩上放置。

　　A. The new gasket selected should be in good condition. Once quality problems such as local fracture are found, it cannot be used forcefully. Before using, the new gasket shall be stored in the original packing box in good condition, and shall not be stacked randomly to make it bent or overlapped, and shall not be placed on the hook.

　　B.安装新垫片前，接缝表面应处理好，使接缝表面光洁无垢。同时，对接头表面进行翘曲检查。

　　B. Before installing the new gasket, the joint surface shall be well prepared to make the joint surface clean and free of scale. At the same time, check the warpage of the joint surface.

　　C.各垫片漏油时，先将泄漏区域的螺丝均匀有序地拧紧。如果泄漏仍然存在，更换新的垫圈。

　　C. When the gasket leaks oil, tighten the screws in the leakage area evenly and orderly. If the leak persists, replace the gasket with a new one.

　　大多数车主发现该车有非正常耗油、涨价的情况，可能是漏油造成的，所以我们应该经常设定北京奥迪A3保养周期来检查油罐。如果发现漏油，应该及时修复，比如更换完好无损的新衬垫。所以如果漏油情况非常严重，应该开车到4S店进行维修。

　　Most car owners find that the car has abnormal fuel consumption and price increase, which may be caused by oil leakage. Therefore, we should often set a Beijing Audi A3 maintenance price cycle to check the oil tank. If oil leakage is found, it should be repaired in time, such as replacing the intact new gasket. So if the oil leakage is very serious, you should drive to the 4S shop for professional maintenance.

　　以上是济南奥迪汽车维修公司小编为大家介绍的相关内容，想要了解更多内容，欢迎访问网站：http://www.lutongqixiu.com

　　These are the relevant contents introduced by Jinan Audi automobile maintenance company. If you want to know more, please visit the website: http://www.lutongqixiu.com