With the aggravation of the market competition, the price of the car girder calibrator is getting lower and lower. Under the premise of low profit, the manufacturer will not send personnel to the site for equipment installation and commissioning. Some employees of maintenance enterprises have used the car beam calibrator, and some new enterprises have never been exposed to this situation. What should we do?

　　济南奔驰汽车维修哪家好

　　Which is the best car repair shop for Jinan Benz

　　很简单:遵循调试步骤。安装调试步骤如下:

　　Simple: follow the debugging steps. The installation and debugging steps are as follows:

　　一个:卸载。目前市场上使用叉车卸车更为方便。叉车必须配备伸直的手臂，这通常被称为伸直的腿。由于超级棒梁校直器的长度一般为5米和6米，如果没有伸出胳膊(伸直腿)，就不够长，使用起来也不方便。(如叉车使用不方便，也可使用吊车)在放置横梁校准仪时，由于小车从起升油缸一侧上升，应将起升油缸的端部翻出。

　　One: uninstall. At present, forklift is the most convenient to unload in the market. Forklifts must be equipped with straight arms, which are often referred to as straight legs. As the length of the super bar straightener is generally 5M and 6m, it is not long enough and inconvenient to use if the arm (straight leg) is not extended. (if the forklift is not convenient to use, the crane can also be used.) when placing the beam calibrator, because the trolley rises from one side of the lifting cylinder, the end of the lifting cylinder should be turned over.

　　二:吊主链和斜吊臂。将光束校验仪放置在预定位置后，用钣金工具拆卸木箱，找到主链。吊链前应安装斜臂，斜臂上应安装带链条的u型链吊架。然后挂起一根链条，将链条与未钩端相连，穿过u形的链条吊架，然后穿过导向环，穿过顶杆帽。注意:链条不允许打结或扭曲。安装链条后，一定要安装链条保护器。

　　2： Crane main chain and inclined boom. After the beam calibrator is placed in the predetermined position, use the sheet metal tool to remove the wooden box and find the main chain. The inclined arm shall be installed before the lifting chain, and the U-shaped chain hanger with chain shall be installed on the inclined arm. Then hang a chain, connect the chain with the uncoupled end, first through the U-shaped chain hanger, then through the guide ring, and finally through the top bar cap. Note: the chain shall not be knotted or twisted. After installing the chain, be sure to install the chain protector.

　　三:连接油管(主要用于气动泵)。箱内有两个气动泵和两个油管，箱内装有钣金件。将油管连接到气动泵上，注意用原材料包裹，防止漏气。当次使用,因为有残余气体在油缸,所以在使用前必须先排气(打开旁边的排气阀气动泵踏板),结束的气动泵连接到空气源、油管快速连接到其他媒体在地上,按气动泵,直到石油耗尽。然后将管子的一端(快速连接)连接到拉塔的气缸上，将脚压在气泵上。此时，油缸将会上升，拉塔中的千斤顶杆也会上升。测试完后，试一下平台上倾斜的油缸。

　　3： Connect oil pipe (mainly used for pneumatic pump). There are two pneumatic pumps and two oil pipes in the box, and the box is equipped with sheet metal parts. First, connect the oil pipe to the pneumatic pump, and wrap it with raw materials to prevent air leakage. When using for the first time, because there is residual gas in the cylinder, it is necessary to exhaust before using (open the pneumatic pump pedal of the side exhaust valve), connect the end pneumatic pump to the air source, connect the oil pipe to other media quickly on the ground, press the pneumatic pump until the oil is exhausted. Then connect one end of the pipe (quick connect) to the cylinder of the tower and press the foot on the air pump. At this time, the cylinder will rise and the jack rod in the tower will rise. After the test, try the tilt cylinder on the platform.

　　四、一步是钣金。板料零件可以挂在板车上。

　　4、 The final step is sheet metal. Sheet metal parts can be hung on the board car.

　　以上是济南奔驰汽车维修公司小编为大家介绍的相关内容，想要了解更多内容，欢迎访问网站：http://www.lutongqixiu.com

　　These are the related contents introduced by the small edition of Jinan Benz automobile maintenance company. If you want to know more, please visit the website: http://www.lutongqixu.com