(1)检查并清洗粗油滤清器，更换滤芯。
(1) Check and clean the crude oil filter and replace the filter element.
(2)拆卸油精过滤器。
(2) Remove oil filter.
检查并清洗油底壳，设置滤清器，检查曲轴轴承紧固度，拧紧曲轴轴承螺栓、螺母。
Check and clean the oil pan, set filter, check the tightness of crankshaft bearing, tighten the bolts and nuts of crankshaft bearing.
(4)热车释放脏油，加入清洗剂，清洗发动机油路。
(4) Hot car releases dirty oil, adds cleaning agent, and cleans engine oil path.
5. 检查并清洁汽油过滤器。
5. Check and clean the gasoline filter.
检查汽油泵和管路。
Check the petrol pump and pipeline.
7 .清洗火花塞碳，纠正电极间隙，检查是否有漏油现象。
7. Clean spark plug carbon, correct electrode gap and check for oil leakage.
今天清洗、检查、调整分配器。
Clean, check and adjust the distributor today.
检查和调整阀门间隙。
Check and adjust valve clearance.
负责进排气歧管的紧固。
Be responsible for tightening intake manifold and exhaust manifold.
清洗发动机空气过滤器和曲轴箱通风空气过滤器。
Clean engine air filter and crankcase ventilation air filter.
清洁曲轴箱通风单向阀和管道。
Clean crankcase ventilation one-way valves and pipes.
拧紧泵的螺栓、螺母，调整风机v形皮带的松紧。
Tighten the bolts and nuts of the pump and adjust the tightening of the V-belt of the fan.
按下列顺序和力矩拧紧气缸盖螺栓。
Tighten cylinder head bolts in the following order and moment.
清洗化油器进口过滤器，清洗化油器壳体，检查联动机构，拧紧连接螺栓。
Clean the carburetor inlet filter, clean the carburetor shell, check the linkage mechanism and tighten the connecting bolt.
参与发动机支架的连接及损坏情况。
Participate in the connection and damage of engine bracket.
负责，拧紧，调整散热器。
Responsible for tightening and adjusting the radiator.
注意，拧紧油箱和油管。
Attention, tighten tank and tubing.
负责，紧固排气歧管和消声器。
Responsible for tightening exhaust manifold and muffler.
监测发动机的燃烧效果，并进行调整。
Monitor the combustion effect of the engine and adjust it.
(2)二级底盘维护
(2) Maintenance of secondary chassis
(1)检查离合器盘和分离轴承;检查分离杆，调整分离轴承与分离杆之间的间隙;调整离合器踏板自由行程;次润滑传动轴前轴承和分离轴承。
(1) Check the clutch disc and separating bearing; check the separating rod, adjust the clearance between the separating bearing and the separating rod; adjust the free travel of the clutch pedal; lubricate the front bearing and the separating bearing of the transmission shaft for the first time.
(2)检查转向节衬套与主销配合是否紧固;拧紧主销水平销螺栓。
(2) Check whether the steering knuckle bushing is tightened with the main pin; tighten the horizontal pin bolt of the main pin.
Jinan Mercedes-Benz automobile repair which good to look for Jinan Lutong automobile repair repair, more knowledge about automobile repair click on the official website for consultation: http://www.lutongqixiu.com/
