汽车发生故障是家常便饭的事情，大部分人都会选择送去修理厂进行修理检查，但是修理厂检查一个很麻烦，而且费用也不便宜，所以车主自己看懂一些常见故障和更换小配件，也是能在紧急情况下解决很多事情的。汽车常见故障如何诊断呢？下面
济南奥迪汽车保养人员就来讲讲车辆安全检查方法吧。
It's a common thing for a car to break down. Most people choose to send it to the repair shop for repair and inspection. However, the repair shop is very troublesome and the cost is not cheap. Therefore, the car owner can understand some common faults and replace small parts, and can solve many problems in an emergency. How to diagnose common automobile faults? Let's talk about the vehicle safety inspection methods by Audi maintenance personnel in Jinan.
汽车外观
Car appearance
注意车身是否整洁、周正，有无明显锈迹和变形；2、检查左右后视镜、内后视镜，应完好、无损毁；3、检查刮水器各挡位是否工作正常；4、检查发动机、水箱，是否有漏油、漏液现象。
Pay attention to whether the vehicle body is clean and upright, and whether there is obvious rust and deformation; 2. Check the left and right rear-view mirrors and internal rear-view mirrors, which shall be intact and free of damage; 3. Check whether each gear of the wiper works normally; 4. Check the engine and water tank for oil and liquid leakage.
制动系统
braking system
检查各车轮制动气室、及制动管路的密封性；2、检查气压表的系统压力是否正常；3、检查制动系统各故障指示灯指示状况是否存在故障；4、检查并指压空气压缩机传动带，是否存在有龟裂的现象。
Check the tightness of brake air chamber and brake pipeline of each wheel; 2. Check whether the system pressure of the barometer is normal; 3. Check whether there is any fault in the indication condition of each fault indicator lamp of the braking system; 4. Check and press the air compressor drive belt for cracks.
转向系统
steering system
检查转向盘各连接处是够有松旷、开裂的现象。
Check whether the joints of the steering wheel are loose and cracked.
转动系统
Rotating system
检查传动轴支架，是否存在有破损和变形的现象；2、检查自动变速器、液力缓速器的密封状况。
Check the transmission shaft bracket for damage and deformation; 2. Check the sealing condition of automatic transmission and hydraulic retarder.
照明、信号灯
Lighting and signal lamp
前照灯应齐全、完好、表面清沽；2、检查信号指示灯的表面是否干净，且工作是否正常。
The headlamp shall be complete and intact, with clear surface; 2. Check whether the surface of the signal indicator is clean and works normally.
轮胎
tyre
检查轮胎外观是否有破裂、凸起、异物刺入等现象；2、检查轮胎磨损情况；3、检查轮胎规格和花纹是否一致；4、检查轮胎的气压是否正常。
Check the appearance of the tire for cracks, protrusions, penetration of foreign matters, etc; 2. Check the tire wear; 3. Check whether the tire specification and tread pattern are consistent; 4. Check whether the tire pressure is normal.
悬架系统
suspension system
检查悬架的弹性元件，是否牢固，有无断裂等情况；2、检查钢板弹簧各部分的零件是否齐全。
Check whether the elastic elements of the suspension are firm and broken; 2. Check whether all parts of the leaf spring are complete.
安全设施
Safety facilities
检查动力启闭车门的机件是否完整；2、检查安全顶窗，安全顶窗机件还否齐全、完好。3、检查安全锤、灭火器是否在指定的位置。
Check whether the mechanical parts of the power door are complete; 2. Check whether the safety top window and its components are complete and intact. 3. Check whether the safety hammer and fire extinguisher are in the designated position.
摄像头行车记录仪
Camera dash cam
检查车内摄像头，摄像头的拍摄方向应符合规定且无遮挡。
Check the camera in the vehicle, and the shooting direction of the camera shall meet the requirements and be free of obstruction.
This is the general description of the vehicle safety inspection method. If you want to use it smoothly for a long time, you need to do more inspections and regular maintenance. You can visit our website for more information http://www.lutongqixiu.com consulting service
