1. The fault is connected to the starting gear of the ignition switch. The starter is idle and cannot engage the flywheel teeth to drive the engine.

　　2、故障原因单向离合器打滑或损坏；拨叉变形、啮合弹簧折断或太软；起动机主开关行程调整不当，以致开关闭合时间过早或起动机固定螺栓松动等。

　　2. Failure causes include slippage or damage of one-way clutch, deformation of fork, breakage of meshing spring or too soft, inappropriate adjustment of main switch stroke of starter, premature closing time of switch or loosening of fixed bolt of starter, etc.

　　3、故障排除

　　3. Troubleshooting

　　①起动机空转时转速很高，可听到高速转动的“嗡—”声，但发动机不转。一般为单向离合器打滑，应检查单向离合器的锁止转矩，并予以检修、调整。

　　When the starter idles, the speed is very high, and the "buzz" sound of high-speed rotation can be heard, but the engine does not turn. Generally, the one-way clutch slips. The locking torque of the one-way clutch should be checked and repaired and adjusted.

　　②起动时伴有齿轮撞击声：应检查啮合弹簧是否折断或过软；起动机主开关行程调整是否合适；起动机固定螺栓是否松动等。可依据检查所见具体情况予以修理。

　　(2) Starting with gear impact sound: check whether the meshing spring is broken or too soft; whether the main switch stroke adjustment of starter is appropriate; whether the fixed bolt of starter is loose, etc. It can be repaired according to the specific conditions seen in the inspection.
汽车电动机出现空转现象的原因！

　　少防眩目前照灯是在近光灯丝上加上了配光屏，使一半的光通量被截止，通过配光镜得到非对称性光型，从而充分限制了迎面车辆驾驶人受到照射的光束，又可使行车路线得到良好的照明，提高了夜间会车的安全系数。

　　At present, the light distribution screen is added to the low-light filament to cut off half of the light flux. The asymmetric light pattern is obtained through the light distribution mirror, which fully limits the light beam to the driver of the vehicle in front of him, and makes the driving route get good illumination, and improves the safety factor of meeting at night.

　　防眩目前照灯的特征是近光灯丝有一块配光屏，而且配光屏与灯丝正投影水平方向成15“偏角，挡住下半部光源。在配光镜玻璃表面左右两边有不对称的花纹，花纹的正方向右下方有偏角巧“的直线，以使汽车在道路右侧行驶时，上方是一个明显的暗区，而在下方及右上15“内是一个亮区，从而达到汽车夜间交会时，避免灯光眩目的效果。

　　At present, the anti-glare feature of the headlamp is that the low-light filament has a light distribution screen, and the light distribution screen and the filament projection are at a horizontal angle of 15 "to block the lower half of the light source. There are asymmetrical patterns on the left and right sides of the glass surface of the light matching mirror, and the right and lower sides of the patterns have a line with a deflection angle, so that when the car is driving on the right side of the road, the upper side is a clear dark area, while the lower and upper right 15 "is a bright area, so as to achieve the effect of avoiding the glare of the lights when the car intersects at night.